Use --algo NEXA to mine it. Be patient please :), Important notes about the new LHR unlocker scheme. Found a share of difficulty 6.51G Pool not reacting to submitted shares for too long. Re: lolMiner 1.43: Real Eth + Ton dual mining - feel the spirit of 2017. [2Miners] Best Ethereum Mining Software for Nvidia and AMD - AZCoin News I will do better Nvidia codes in the future, but preparing it takes time. Fixed a bug causing --dualworker not to work right with Kaspa dual mining. Slightly improved dual mining performance of Ethash + Alephium on AMD RX 5000 and RX 6000 series, Slightly improved energy efficiency of Ethash on AMD RX 5000 and RX 6000 series, New memory management for Ergo on Nvidia GPUs. Ethash: Added error correcting tables to check the DAG integrity up to epoch 499 (Early June 2022). Added Eth/Etc/Ubiq + Kaspa dual mining solver for AMD RX 400, 500, 5000 and 6000 series and Nvidia RTX 2000 / 3000 series. The core clock used for the GPUs. HiveOn, Nicehash) (1), Fixed an issue that might cause the epoch to update too late when doing Eth + Zil dual stratum, Fixed an issue causing too much stale or very late shares in Ergo, Fixed partially defect .bat example files. Use --disable-dag-verify to disable the verify & repair mechanism routine. This solves issues with unstable proxy forwarding e.g. To continue mining Ergo, please update to this version. Fixed a bug with json style configuration not working with dual mining in 1.43 release version. The archives for ZIL example files now contain examples how to bypass the ZIL pools. This fixes an issue when a pool went offline and the following connection attempt takes indefinitely much time. Improved system memory footprint when mining Flux or Beam on Nvidia GPUs. lolMiner Windos and Linux. Temperature to pause or stop a GPU from mining in degree C. If set to 0 disables stop above a fixed temperature. It is more stable now. Note: please do not use the new 515.x drivers - on them the unlock currently does not work. Gain is 15-20% over the old implementation at same Eth reward - combined with new tuning some cards can be much higher (e.g. Default value is 0 (off), for most cards the value of 2 is optimal. Therefore in automatic mode the miner might start with a slightly slower hash rate at the beginning, but will get better over time. From v1.53 If the pool share latency is above this value and failover pools are configured, the miner will terminate the connection and connect to the next failover pool (at the earliest after 10 shares on the active connection). You can control its behavior with the parameter, Updated internal libraries for TLS connection handling. Use a comma separated list of values if you want to assign different values for each GPU. The miner itself will take no further action and continue operation on the remaining cards. This has advantages when your normal DNS resolving might be blocked or modified by a firewall. Note that existing dual mining configurations will automatically launch Eth / Etc / Ubiq only mode, so existing configurations will not be broken. Cards are separated with a comma. The needed calibration will get better over time, but the things learned are too complex to display them or store into parameters. To prove that you are working on the problem, you submit what are called shares. ), Fixed performance regression on Nvidia cards, Added support of Ethash and Beam Hash III for RX 6000 generation of GPUs. Fixed 3060 V1 (GA106-300-A1) internal parameters for drivers 460.39 and below, stabilizing the hash rate (they pretty much did not work stably unlocked in 1.36), Fixed a bug causing a wavy hash-rate report in some FHR rigs. Use --tstart to allow a restart of the card below a lower temperature. Added detection of the "fan glitch" for RTX 3000 LHR cards. Ethereum stratum code will now print the pool difficulty in better human readable number, The miner will now print the ip of the connected pool - to be able to detect e.g. Unlocking & reducing --lhrtune parameter. Use --tstop to stop any mining operation on a GPU at the given temperature. Reduced Ton & Alephium fee in Eth+Ton / Ethash+Alephium dual mining to. Tuning advice: On Nvidia Turing and Ampere GPUs this algorithm works best when locking the core clock to desired value (higher gives more performance, lower reduces power draw). GPU 1: Found a share of difficulty 46.24G GPU 1: Share accepted (11 ms) The text was updated successfully, but these errors were encountered: All reactions Copy link . Updated web ui for supporting Intel GPUs, more pools and coins. b) For mining an other algorithm with your 4G cards: Slight rework of Beam Hash III back end. 3080 12GB Results 1.43 Issue #999 Lolliedieb/lolMiner-releases So for example if the factor is 25 and the Eth hash rate is 59.5 mh/s, then the dual hash rate will be 25 times 59.5 mh/s = 1487,5 mh/s. An other performance improvement of Flux mining on Ampere based GPUs (1.5 - 3.5% depending on model and clocks), Fixed a bug causing some Ergo pools to disconnect the miner frequently (Introduced with 1.56 :/ ), Major performance increase for Flux mining on Nvidia Ampere GPUs, Major performance increase for Beam mining on Nvidia Ampere GPUs, Mining Flux and Beam on all Nvidia GPUs now uses Cuda instead of OpenCL, Slight performance improvements for Flux mining on AMD RX 500, RX 5000 and RX 6000 (about 0.2 it/s), Mining any Equihash based coin (Flux, BTG, Aion, ) now supports extra nonce subscription via stratum (e.g. Added new dualmode eth. Minimal temperature for a GPU to start in degree C. If set to 0 disables restart below a fixed temperature. Values given to --dualfactor parameter will now be value checked and rounded / capped to working values. You signed in with another tab or window. 1.36a: Reverted some LHR kernels to a specification more similar to what was in 1.35. Use --4g-alloc-size to calibrate the number of MBytes the GPUs are allowed to use.
If One Strawberry Has Mold Are The Rest Bad,
Articles F
